bt_iso_recv() in subsys/bluetooth/host/iso.c pulled the ISO SDU header (4 bytes) or, when the timestamp flag is set, the timestamped SDU header (8 bytes) from the inbound HCI ISO Data buffer via net_buf_pull_mem() without first checking buf->len. The upstream hci_iso() handler enforces buf->len == the controller-declared ISO Data_Load length, so a malicious or buggy controller / adjacent BLE peer on an established CIS/BIS can present a first-fragment (BT_ISO_START) or single (BT_ISO_SINGLE) PDU shorter than the SDU header. Because net_buf_simple_pull_mem only guards length with __ASSERT_NO_MSG (compiled out when CONFIG_ASSERT is disabled, the production default), the pull underflows buf->len (uint16_t, e.g. 0 - 8 = 0xFFF8) and advances buf->data past valid data: the subsequent reads of hdr->slen and hdr->sn are out-of-bounds reads of adjacent pool memory. For the multi-fragment (START) case the corrupted buffer is retained as iso->rx, and a following CONT/END fragment's net_buf_tailroom() guard underflows to a near-SIZE_MAX value, defeating the bounds check and causing net_buf_add_mem() to memcpy attacker-supplied fragment data far past the RX pool buffer (out-of-bounds write). The flaw affects ISO receive builds (CONFIG_BT_ISO_RX, selected by the default-off LE Audio options BT_ISO_PERIPHERAL/BT_ISO_CENTRAL/BT_ISO_SYNC_RECEIVER) and has existed since the ISO subsystem was introduced (v2.6.0) through v4.4.0. The fix adds explicit buf->len < sizeof(ts_hdr) and buf->len < sizeof(hdr) checks that drop the buffer before pulling.
Metrics
Affected Vendors & Products
| Vendors | Products |
|---|---|
| Zephyrproject-rtos |
|
No data.
No data.
References
History
Tue, 14 Jul 2026 19:00:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | A missing length validation in the Zephyr Bluetooth Host ISO receive path can be triggered by malformed HCI ISO data. In bt_iso_recv() (subsys/bluetooth/host/iso.c), when processing PB=START/SINGLE fragments, the code pulls a TS SDU header (8 bytes, ts=1) or a non-TS SDU header (4 bytes, ts=0) without first verifying that buf->len contains at least that many bytes. The outer HCI ISO length check in hci_iso() validates payload length consistency but not the minimum inner SDU header size, so a packet with payload length 1 passes hci_iso() and then reaches net_buf_pull_mem(), which asserts buf->len >= len. As a result, malformed ISO traffic deterministically triggers a kernel assert (denial of service) in assert-enabled builds, and in non-assert builds the same path may proceed with an undersized buffer, leading to out-of-bounds read behavior. The issue affects products using the Zephyr Host with CONFIG_BT_ISO_RX enabled, particularly where incoming HCI data can be influenced by a malicious or compromised controller or malformed forwarded ISO traffic. | bt_iso_recv() in subsys/bluetooth/host/iso.c pulled the ISO SDU header (4 bytes) or, when the timestamp flag is set, the timestamped SDU header (8 bytes) from the inbound HCI ISO Data buffer via net_buf_pull_mem() without first checking buf->len. The upstream hci_iso() handler enforces buf->len == the controller-declared ISO Data_Load length, so a malicious or buggy controller / adjacent BLE peer on an established CIS/BIS can present a first-fragment (BT_ISO_START) or single (BT_ISO_SINGLE) PDU shorter than the SDU header. Because net_buf_simple_pull_mem only guards length with __ASSERT_NO_MSG (compiled out when CONFIG_ASSERT is disabled, the production default), the pull underflows buf->len (uint16_t, e.g. 0 - 8 = 0xFFF8) and advances buf->data past valid data: the subsequent reads of hdr->slen and hdr->sn are out-of-bounds reads of adjacent pool memory. For the multi-fragment (START) case the corrupted buffer is retained as iso->rx, and a following CONT/END fragment's net_buf_tailroom() guard underflows to a near-SIZE_MAX value, defeating the bounds check and causing net_buf_add_mem() to memcpy attacker-supplied fragment data far past the RX pool buffer (out-of-bounds write). The flaw affects ISO receive builds (CONFIG_BT_ISO_RX, selected by the default-off LE Audio options BT_ISO_PERIPHERAL/BT_ISO_CENTRAL/BT_ISO_SYNC_RECEIVER) and has existed since the ISO subsystem was introduced (v2.6.0) through v4.4.0. The fix adds explicit buf->len < sizeof(ts_hdr) and buf->len < sizeof(hdr) checks that drop the buffer before pulling. |
| Title | Bluetooth Host ISO RX Missing SDU Header Length Validation in bt_iso_recv() Leads to DoS | Out-of-bounds access in Bluetooth ISO receive (`bt_iso_recv`) due to missing SDU-header length validation |
| Weaknesses | CWE-787 | |
| References |
|
Tue, 23 Jun 2026 13:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Weaknesses | CWE-125 | |
| Metrics |
ssvc
|
Tue, 23 Jun 2026 02:45:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| First Time appeared |
Zephyrproject-rtos
Zephyrproject-rtos zephyr |
|
| Vendors & Products |
Zephyrproject-rtos
Zephyrproject-rtos zephyr |
Tue, 23 Jun 2026 00:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | A missing length validation in the Zephyr Bluetooth Host ISO receive path can be triggered by malformed HCI ISO data. In bt_iso_recv() (subsys/bluetooth/host/iso.c), when processing PB=START/SINGLE fragments, the code pulls a TS SDU header (8 bytes, ts=1) or a non-TS SDU header (4 bytes, ts=0) without first verifying that buf->len contains at least that many bytes. The outer HCI ISO length check in hci_iso() validates payload length consistency but not the minimum inner SDU header size, so a packet with payload length 1 passes hci_iso() and then reaches net_buf_pull_mem(), which asserts buf->len >= len. As a result, malformed ISO traffic deterministically triggers a kernel assert (denial of service) in assert-enabled builds, and in non-assert builds the same path may proceed with an undersized buffer, leading to out-of-bounds read behavior. The issue affects products using the Zephyr Host with CONFIG_BT_ISO_RX enabled, particularly where incoming HCI data can be influenced by a malicious or compromised controller or malformed forwarded ISO traffic. | |
| Title | Bluetooth Host ISO RX Missing SDU Header Length Validation in bt_iso_recv() Leads to DoS | |
| References |
| |
| Metrics |
cvssV3_1
|
MITRE
Status: PUBLISHED
Assigner: zephyr
Published: 2026-06-22T23:58:47.022Z
Updated: 2026-07-14T18:38:41.661Z
Reserved: 2026-06-02T15:24:35.422Z
Link: CVE-2026-10658
Vulnrichment
Updated: 2026-06-23T12:20:52.868Z
NVD
No data.
Redhat
No data.